So close I can taste it!

So, I´m back with an update.... FINALLY! ;) I went from the Ultimarc Mag-stik Plus to the Ultrastic 360 (In the picture above). There is a very big difference between these two joysticks as they connect very differently to your computer. The Mag-stik uses standard spade connectors and all directions of the stick has to be wired to a joystick interface like the Ultimarc Mini-Pac. These interfaces are used to fool your computer into believing that you´ve attached a keyboard.

This is the lower part of the Ultrastic 360. It has its own interface card on board. This way I can connect up to 8 buttons and let each joystick program these. It also uses a non-contac magnet instead of physically pushing connectors to give orders to the computer. The joysticks I received was waaaaay to soft for my liking. Also the ball-top handle was to short for my hands. I had to order harder springs, new handles and also two plastic restrictors (The clear plastic with jagged edges in the above pic) to restrict the movement of the joystick. I have to say that it was a bit of a hassle to change the parts.

Here you see the control panel so far. I´ve attached the joysticks via Rasmus Koenigs superb invisible joystick bracket that has been glued to the backside of the CP. It was just for me to put each joystick on the brackets and fasten them with shims and nuts. I´ve also drilled holes for screws for fastening the CP to the cabinet. They´ve been counter sinked so that they´re flush with the artwok, but still available if any crisis should occur.

But there is one thing that is bugging me. The lower 1-player action button collides with the left 1-player button. This is a real problem!! I might have to switch to shorter buttons on the player-1 button. This is not a design flaw, bu rather me fu.... up the original drawings... Note to self. 1. Next time I´ll fit the cabinet to the CP and not the other way around. 2. MDF-CP FTW!! Alu is not an option for future projects!

Thanks for reading, and do not hesitate to mail me with any question you might have!

Cheers!
Bjorn

Aluminium Control Panel

I am so sorry for my absence lately. Work has got the best of me! I just finished the control panel for Project Peach. It has taken me soo long because I did not have a lazer cutter near by. That would have solved it as it would just follow the CAD-file and fix it with pin-point accuracy. I bent it using a large bending machine, and then made the holes with a 29mm hole saw that I kept cool with some cutting fluid. 

I attached the buttons and found out that there is a small challenge with the Player1-button to the far left on the vertical part of the panel. The button goes so far in that it collides with the lower action-button on the player1-set above it. This is not good. If all else fails, I have to buy new and shorter buttons. That´s fine by me, but it is money I don´t have right now...

The foil I´m using for the CP (Control Panel) is printed at Allkopi. I´ve used the Orajet foil that can be printed on, but I´ve also ordered Allkopi to laminate it with Oraguard Laminating film 250AS. This is a non stick foil used for floors and table surfaces. It is non-stick and withstands "sweatty hands-syndrome".
The main reason for using this foil is that I´m dropping the use of clear acrylic on top of the CP. From what I remember, this foil was used on most of the arcades I used to play when I was a boy. 
I pray to the elder gods that the holes on the CP fits the holes on foil. If not....It all ends here.... ;)

Easter Update!!!

Got some work done today. Mostly cleaning up the cables and checking the general setup of the cab. I wish it was better planned and tidier, but it´s not always easy thinking ahead. The picture above shows the inside of the cab and the finished (almost) backpanel. The idea with the window on the backpanel is not to get at view of the cables. The idea is that I´m going to place a sheet of white or black powder coated aluminium about 1.5cm in so that it covers the pink cathode, and hides the interior of the cab. The logo is ment to glow.

The sensor in the top right corner of the back panel is a thermometer so that I can check if the thing is on fire...

Here is the cab fired up. The pink light is a bit hefty in this photo. I looks alot mor subtle, and it will be aimed more precisely when I attach the panel behind it. The two buttons on the upper left is marquee light and the pink logo-light. Looks nice so far!

I had to include a shot of the volume button ;) It´s a custom made knob(!) used on children shelfs and cubbords. Turn it clockwise and enjoy the ruckus!

Here you can see two holes that I drilled for the power and hard drive diode. It was not planned and I just did it there and then. Probably going to find a clear circular cover for each hole. Guess its important to know if the thing is on or not ;)

Witness the hotness! Important to know the temperature inside the cab when it´s all covered and shut. Cheap and easy to install. Thank you Ebay!!!

Much happier with the way the marquee is being lit. First I attached the cathodes at the top and bottom inside the "marquee bay". Did not work out exactly as I hoped. I bent som 1.5mm aluminium and made two brackets that hangs from the top and is placed dead center. Looks alot better now! Hopefully the heavy duty double sided tape will not loosen when it gets hot... I´ve had some accidents the last days ;)

STOP THE PRESS!!!

The USBs have no power... I´m having a breakdown here.... Got to have a look at it tomorrow. Could be a cable or two that I didn´t attach to the motherboard. Please say it´s so! I can´t replace the 300W PSU. Everything is built around it! GAH!! THE HUMANITY! :(

All work and no play makes Bjorn a dull boy...

Sorry for quiet times guys! Got my pedadogy exam paper that needs to be written. Will come back with more info on the cab as soon as this abomination has been handed in ;)

Cheers

Bjorn

New header for March

Just a visual update on the header. Street Fighter 2 was a game I really sucked at playing. I really did not have the skills to remember more than the "Haduoken"-move. But what else was there to remember. That move defined SF2 more than any other. Ah! Being 12 and sitting pennyless watching SF2 demo mode ;) Header pic was illustrated by the art collective Udon.

Back panel more or less done :)

I´ve used a foam roller to apply paint to the whole Weecade. The idea was to get the surface as smooth as possible. Still I must admit that it is not smooth enough. I end up with a glossy surface but with small even bumps. So I expect that my next project will be painted with a Bosch PFS 65 Electric Paint Sprayer. I know it takes a bit of practice, but to get the surface even this is my last resort :) So much easier to get to all the hard places.

The feedthrougs have been attached and working perfectly as with the power socket. It really made the difference! The volume button is still in the makings, but as soon as I get hold of a 28mm hole drill, I will get to it.

I must say that that this project is not a 100% accurate measure wise. It has been really hard as I started out without being thorough enough. Quality rulers and lazer measuring should be first priority. The opening for the back panel is about 2mm tighter at the top then at the bottom. This is of course not a good thing for the back panel ;)

Still, we´re on course and hoping to finish up the build soon. The control panel is at hand and will be quite a challenge. There is no room for measure errors between the decor foil and the metal itself... Not looking forward to that one ;)

Regards

Bjorn

"Damn the torpedoes, full speed ahead!"

This has been a more or less perfect day when it comes to tinkering. First I spent a good deal of time measuring the holes for the thermometer and power socket. I wanted the two holes to be aligned to the overhead holes so they look all nice and dandy. Thanks to one giant stationary drill (Not the Bosch this time) I got it all fixed perfectly. The holes ended up spotless and dead centered.

I also had an idea when it came to the volume button. As the amplifier card resides INSIDE the machine, and the volume pin goes through the back cabinet panel I though about sinking a button about 4mm into the back panel. To simplify it, I´m going to make it look as the button is not outside of the back panel, but rather that it resides 4mm into the panel...Sigh.. Look at the pictures then ;) Anyways, the result was perfect. I could have messed this one up badly as I only needed the button itself to be 1-2mm out of center for it to "throw". The button also needs to be able to also survive the wear and tare of being attached and detached whenever I need to access the interior.

And also, the buttons, thermometer and power socket fit like a glove! To the right you se the "sinked" hole with the center hole for the volume pin. The hole is 30mm and the button will have a diameter of 28mm. That gives ruffly 1mm of play...Hmm.. Might to a smaller button. I might miss and end up with more than 1mm of throw... That would render the button useless. Oh! The humanity!

Before priming and painting the back panel, I would like to mention how much work this was. I have no previous experience with routing or precision drilling so this was a huge leap for me (mankind can come too!) The areas that are sinked are routed so that the air vents at the top can fit the pink perforated steel-sheet. The lower window will house the acrylic logo-window. The latter is just for show. It does not have any function except estetically.

Here I´m done with the cutting and drilling of the back panel. I´ve primed it twice (only a light sanding between each coating). It´s now drying and is ready for two coats of glossy paint. As you probably notice I´ve left out painting the holes. They were so spot on that I could jeopardize how well they fit. The paint is also sticky and have a slight glue-effect. We don´t want stuck buttons now do we?!?!

And one last thing... The marquee lit up today ;) I have to say it looked really good. The two white cold cathode tubes inside gave quite a cold light, but this can be fixed with some foil used on studio lamps that lowers the Kelvin from 5500 to 3500 (Winter to summer-light). PS. The lighting will be a bit more even when the white back panel is included.

Again, this is so fun it hertz!

Hope ya´ll like it! Remember to leave comments. I believe I´ve finally managed to set Blogger up so that you can comment without having to be member of some stupid plan or software...

Regards

Bjorn

Buttons and feedthroughs

I guess I should be offering something more than just a button/feedthrough update, but this was not an easy task. To get all the holes aligned and the perfect size was quite a task. Still I am very happy with the result. Tomorrow I´m going to install the thermometer and power socket. I´m also tinkering with a volume button solution. Could be fun! Things are speeding up! This project is now closing in on one year from I first started. Serving a family, refurbishing a house, working 100% as a teacher AND taking a uni course doesn´t leave much idle time ;)

About the picture: It shows the back panel of the Weecade. On top you see the air vents that are going to be covered with perforated steel from the inside. Below them you see the large "logo window" that will be sporting a acrylic window with the "Project Peach" logo in grey "ice" foil.

The connectors at the lower part is from the left: Marquee light, "Logo window"-light, black ON/OFF-button. USB 1/2 and 3. They´re for keyboard, mouse and external drive/CD-Drive. The weecade has a wireless card so it´ll be online from birth. The small little pin at the bottom is the volume button. I am going to sink the button about 4mm into the MDF....hopefully....

Tomorrow I say!!!

Regards

Bjorn

IT´S ALIVE!!! Great success I say!!

Good news everyone! Science has been done, and it is a success. It runs silent and...deep? I feared the worst when it came to tapping power from the PSU to the amplifier-card as I´ve heard rumors about massive noise issues. Luckily there was no problems at all :) When I first tried to start it up I had some issues due to the fact that I had put the "Reset" cable on "Reset". I was supposed to be on the "Power" pins on the mother board. When it finally fired it was like I just had inventet penicillin or something. This was a massive science-leap for such a scatter brain as my self. Epic times! PS: It´s supposed to be alot more tidy in there...

But it wasn´t easy. Because I installed the Noctua 90mm fan, it just made everything so much harder. I don´t think the fan was even needed... Positioning the motherboard was also a real hassle as there just weren´t enough room. It worked, but it was pure Hell to get to all the screws.

Tomorrow I will drill holes in the backplate to include the following: ON/OFF-button, marquee lights and back logo light, three USB feed throughs, thermometer and power socket with ON/OFF-button. All the Weecades I´ve seen has used a mounted MDF-plate connected to the cab and not to the back panel. I know this is not the best solution, but there is no room for mounting such a plate. I´m going to make a template for the drilling as I will surely drill myself in the head if I mess up the back plate. It has taken me forever to saw, rout and drill. Fingers crossed!

I´m also getting my hands on a second hand (FREE!!!) 120gb 2.5" harddrive from my friend Stig. Then it´s all about the control panel... which I dread... WHY oh WHY did I make it out of sheet steel. Why not MDF? I have developed such an intimate relationship to this material. It is almost a part of me now. At least my nose agrees! Dusty stuff...

It was so hard to leave the workshop today. I had to pick up my daughter from kindergarden, but I wanted so bad to stay for more science (Christ, I´m 14 again...). Tomorrow I´m back on the horse and hoping for more win! It´s just standing there waiting for me ;)

Stuff is really speeding up! Stay tuned for updates tomorrow! This stuff is crazy fun!

"Oh, in the name of God! Now I know what it feels like to be God!"

Frankenstein (1931).

Regards

Bjorn

The Belly of The Beast

My apologies people. I´ve been so busy with work and family. I do believe we´ve had the flu like ten times this season :c/ Right now the cab is at my fathers workshop, and I am seriously considering setting up my own garage here at home. This hobby is without doubt turning into a lifestyle ;)

I´ve been fearing this part of the process a lot. One of my shortcomings in life, is that I do stupid mistakes. What looks good now, might be totally messed up ten minutes later as something else should be in its place. The installment of the 90mm Noctua fan (centered) messed up many of my layout options. The psu was especially hard to fit as I need alot of room around it for cables and so on.

You´ll probably notice that the motherboard-power cable is a bit short. I´m currently looking for an extension for this so that I can reach the motherboard and keep it all as clean as possible. The motherboard needs to be elevated a wee bit so that I can utilize as much of the space as possible. I also need to install a 2.5" HD, CD-Drive (Might skip and go for USB install), USB-WiFi and powercables.

The motherboard is Atom based and has passive cooling. I´m trying to push a lot of fresh air through the cab to keep it happy. The Noctua fan is running at 1000RPM with a resistor connected. I have the option to run it at 1300RPM if needed.

My weeks to come look a bit more low key so that I might focus on attaching the parts and moving on the the most dreaded part: The damn control panel ;)

Cheers!

Bjorn

Fight for our rights!

Closed to protest SOPA and PIPA :(

Introducing the Bosch PBD 40 Stationary Drill

So what did I get for Christmas? Well I got this...a Bosch stationary drill. Before stating that I´ve gone completely mad I have to add that this tool is a paradigm shift for me when it comes to accuracy.

It is not easy to drill perfectly straight or keeping the right drill depth through out your project. With this tool its a breeze. I sports a cross laser for accuracy, enough torque to break your arm and also a complete control of drill RPM. At the price of 364$ many pro-craftsmen will probably shake their heads, but I have to say that this machine has great build quality. It resides in the area between the crappy cheap Chinese stuff, and the overly expensive drills which also seconds as earth core drills ;)

This will take my cabinet projects light years ahead quality wise!

In short, I love it!

WHY U NO WRITE IN ENGRISH???

After being repeatedly e-mailed regarding the fact that I´ve been writing this blog in Norwegian, I´ve now budged and will start translating the entire blog, and from now on using the good Queens English (or at least die trying).

The "Just use Google 2 translate" just does not work as you´ll probably end up with a bunch of non-consistent bla bla and so on.

Anyways, I would like to welcome you all to a more international blog! The russian lurker-sites that has been visiting can come too! (Yes I see you in my statistics).

Please do leave comments for my posts even though I know registering with Blogspot is a Hell of a hassle :/

Game on!